What is meant by saying that the electric potential at a point is 1 volt ?
Electric potential at a point is 1 volt means 1 joule of work is done in moving 1 unit positive charge from infinity to that point.
(a) How many milliamperes are there in 1 ampere ?
(b) How many microamperes are there in 1 ampere ?
How many electrons are flowing per second past a point in a circuit in which there is a current of 5 amp ?
Give two reasons why nichrome alloy is used for making the heating elements of electrical appliances.
Keeping the potential difference constant, the resistance of a circuit is halved. By how much does the current change ?
Name the law which relates the current in a conductor to the potential difference across its ends.
A current of 5 amperes flows through a wire whose ends are at a potential difference of 3 volts. Calculate the resistance of the wire.
Distinguish between good conductors, resistors and insulators. Name two good conductors, two resistors and two insulators.
How should the two resistances of 2 ohms each be connencted so as to produce an equivalent resistance of 1 ohm ?
A wire that has resistance R is cut into two equal pieces. The two parts are joined in parallel. What is the resistance of the combination ?
Three resistors are connected as shown in the diagram.
Through the resistor 5 ohm, a current of 1 ampere is flowing,
(i) What is the current through the other two resistors ?
(ii) What is the p.d. across AB and across AC ?
(iii) What is the total resistance ?
For the circuit shown in the diagram below :
What is the value of :
(i) current through 6 Ωresistor ?
(ii) potential difference across 12 Ω resistor ?
An electric heater is connected to the 230 V mains supply. A current of 8 A flows through the heater.
(a) How much charge flows around the circuit each second ?
(b) How much energy is transferred to the heater each second ?
What is the general name of the substances having infinitely high electrical resistance ?
The p.d. across a lamp is 12 V. How many joules of electrical energy are changed into heat and light when :
(a) a charge of 1 C passes through it ?
(b) a charge of 5 C passes through it ?
(c) a current of 2 A flows through it for 10 s ?
How does the resistance of a wire vary with its :
(a) area of cross-section ?
(b) diameter ?
A piece of wire of resistance 20 Ω is drawn out so that its length is increased to twice its original length. Calculate the resistance of the wire in the new situation.
How should the two resistances of 2 ohms each be connencted so as to produce an equivalent resistance of 1 ohm ?
How much work is done when one coulomb charge moves against a potential difference of 1 volt ?
What do you understand by the term “electric potential” ? (or potential) at a point ? What is the unit of electric potential ?
The graph between V and 1 for a conductor is a straight line passing through the origin.
Which law is illustrated by such a graph ?
What should remain constant in a statement of this law ?
A p.d. of 10 V is needed to make a current of 0.02 A flow through a wire. What p.d. is needed to make a current of 250 mA flow through the same wire ?
What would be the effect on the resistance of a metal wire of :
(a) increasing its length ?
(b) increasing its diameter ?
(c) increasing its temperature ?
Two resistors, with resistances 5 Ω and 10 Ω respectively are to be connected to a battery of emf 6 V so as to obtain :
(i) minimum current flowing (ii) maximum current flowing
(a) How will you connect the resistances in each case ? .
(b) Calculate the strength of the total current in the circuit in the two cases.
(a) Name a device that helps to measure the potential difference across a conductor.
(b) How much energy is transferred by a 12 V power supply to each coulomb of charge which it moves around a circuit ?
Why should the resistance of :
(a) an ammeter be very small ?
(b) a voltmeter be very large ?
A student made an electric circuit shown here to measure the current through two lamps.
(a) Are the lamps in series or parallel ?
(b) The student has made a mistake in this circuit.
What is the mistake ?
(c) Draw a circuit diagram to show the correct way to connect the circuit.
Use the proper circuit symbols in your diagram.
Fill in the following blank with a suitable word :
Ohm’s law states a relation between potential difference and……………………
(a) What is meant by the “resistance of a conductor” ? Write the relation between resistance, potential
difference and current.
(b) When a 12 V battery is connected across an unknown resistor, there is a current of 2.5 mA in the circuit. Calculate the value of the resistance of the resistor.
(a) Define the unit of resistance (or Define the unit “ohm”).
What happens to the resistance as the conductor is made thinner ?
Keeping the potential difference constant, the resistance of a circuit is doubled. By how much does the current change ?
(a) Why do electricians wear rubber hand gloves while working with electricity ?
(b) What p.d. is needed to send a current of 6 A through an electrical appliance having a resistance of 40 Ω ?
(a) Give two examples of substances which are good conductors of electricity. Why do you think they are
good conductors of electricity ?
Calculate the resistance of a copper wire 1.0 km long and 0.50 mm diameter if the resistivity of copper is 1.7 × 10-8 Ωm.
Will current flow more easily through a thick wire or a thin wire of the same material when connected to the same source ? Give reason for your answer.
(a) Give one example to show how the resistance depends on the nature of material of the conductor.
(b) Calculate the resistance of an aluminium cable of length 10 km and diameter 2.0 mm if the resistivity of aluminium is 2.7 x 10-8Ωm.
How does the resistance of a wire change when :
(i) its length is tripled ?
(ii) its diameter is tripled ?
(in) its material is changed to one whose resistivity is three times ?
Calculate the area of cross-section of a wire if its length is 1.0 m, its resistance is 23 Ω and the resistivity of the material of the wire is 1.84 x 10-6 Ωm.
